To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
door lock error
Beside this, How do you fix the F code on a Whirlpool Cabrio washer?
– Unplug the washing machine for 2 minutes and then plug it back (it will help the appliance re-conduct self-diagnostics and conclude that there is no breakdown);
– Press the START and PAUSE buttons simultaneously and hold them for 1 minute to clear the error code.
Likewise, What does Code F mean on Whirlpool Cabrio washer?
door lock error
Also, What does F mean on a washer?
component problem
How do you clear the error code on a Whirlpool Cabrio washer?
– Touch any key from the display pad to clear the error code or press Pause/Cancel key if possible.
– Choose another new cycle and press “Start” key to begin.
– Disconnect the power if the error returns.
– Wait 15 to 30 seconds and restore power.
21 Related Question Answers Found
What does F1 mean on a Cabrio washer?
The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose.
How do you clear the fault code on a Whirlpool Cabrio?
Try the Cabrio Reset Procedure Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.
How do you clear the error code on a Whirlpool Duet washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you fix the F 28 code on a Whirlpool Duet washer?
– Unplug the electrical cord from the wall outlet.
– Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place.
– Remove the detergent tray screws using a Phillips screwdriver and pull off the tray.
– Find the control console unit reset lever and pull it toward you.
What does F mean on Whirlpool washer?
door lock error
How do I reset my Whirlpool Cabrio washer?
Try the Cabrio Reset Procedure Or you can press PAUSE/CANCEL. Choose a cycle and press START. Then disconnect the Cabrio from power if you see the issue or error come back. Wait five minutes.
How do I fix my Whirlpool Cabrio uL code?
If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
How do you reset a front load washer?
– Press POWER to turn the washer off.
– Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
– With the power disabled, press and hold the START/PAUSE button for 5 seconds.
– Plug the washer back in, or turn the circuit breaker back on.
How do I fix my uL washing machine?
UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.
What does F 20 mean on a washer?
An F20 or FH error code indicates a water supply problem. … Both hot and cold water must be connected and turned on. Water inlet hoses kinked. Water inlet valve screen clogged. Water pressure less than 10 psi.
How do I reset the control panel on my Whirlpool Duet washer?
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. You can manually unlock the washer by removing the top (remove screws on the back of the top panel and slide the top panel back to lift off.
How do you reset a washing machine?
First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians.
Last Updated: 17 days ago – Co-authors : 14 – Users : 6
