The error code “F9” indicates a failure with the latch motor. Since the door did not physically lock, open the door and locate the door light switch plunger. Push and hold the door light plunger in and then press Clear/Off while continuing to press in on the door plunger.
– Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. …
– Open the oven door and check the door latch. If it wiggles, it needs to be tightened. …
– Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. …
– Press the oven door shut gently. …
– Test the oven.
Beside this, What does it mean when your oven says F9?
automatic door lock
Likewise, How do I fix the F9 on my Whirlpool oven?
– Power unit down by turning off the circuit breaker(s) for one (1) minute.
– Power unit up by turning on the circuit breaker(s).
– Monitor the range or oven for one (1) minute to ensure the error code does not display again.
– Verify the range or oven operation.
Also, How do I fix error code F9?
The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.
What does it mean when my oven says F9?
An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. … The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.
21 Related Question Answers Found
How do you fix error F9 on LG oven?
Try to reset the unit by either unplugging the range or switching circuit breaker to “off” position. 5. Advise customer to leave it “as is” for 3 to 5 minutes then re-plug or switch breaker back “on”.
How do you clear a Whirlpool oven code?
Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E0 persists then replace the electronic oven control.
What is a F9 code on a LG oven?
If the Control Panel Display lights up error code “F-9” it means oven failed at exceeding 150ºF after 5 minutes of preheating. 3. Have customer press the Clear/Off button to terminate the beeping alarm. 4. Try to reset the unit by either unplugging the range or switching circuit breaker to “off” position.
What does F9 on a stove mean?
error code
How do I fix the F9 code on my Whirlpool oven?
– Power unit down by turning off the circuit breaker(s) for one (1) minute.
– Power unit up by turning on the circuit breaker(s).
– Monitor the range or oven for one (1) minute to ensure the error code does not display again.
– Verify the range or oven operation.
How do I get my Whirlpool oven out of lock mode?
– Press Cancel/Off key to start a latch reset, wait 20-30 seconds and open door.
– Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on.
– Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
Why is my LG oven won’t heat up?
The most common cause for an LG gas oven not heating properly is a bad igniter. The igniter draws electrical current through the safety valve to heat up and ignite the gas in the oven burner. If the igniter weakens or otherwise fails, the gas won’t ignite and your oven won’t heat.
Why does my Whirlpool oven say Loc?
LOC error normally means that it is child locked. You have to press and hold one of the buttons for ten seconds depending on the model. Start by trying the ‘Start’ or ‘Cancel’ button.
What does F9 mean on LG oven?
If the Control Panel Display lights up error code “F-9” it means oven failed at exceeding 150ºF after 5 minutes of preheating. 3. Have customer press the Clear/Off button to terminate the beeping alarm. 4. Try to reset the unit by either unplugging the range or switching circuit breaker to “off” position.
How do I clear F9 code?
– Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. …
– Open the oven door and check the door latch. If it wiggles, it needs to be tightened. …
– Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. …
– Press the oven door shut gently. …
– Test the oven.
How do I turn my oven lock off?
– Try the following to unlock the door:
– Disconnect power to range for 30 seconds. Reconnect power and see if door will unlatch.
– If door does not unlatch and you do not have food in the oven, set the oven up to clean for 1-2 hours. Wait approximately 30 minutes for the oven to cool and try to unlock the door.
How do I put my Whirlpool oven in diagnostic mode?
Last Updated: 6 days ago – Co-authors : 4 – Users : 8
