Feather finish irregular floors. Designed to smooth grooves, joins, gaps and grout joint lines over concrete, terrazzo and ceramic tiles. … Feather Floor is easily applied to any prepared surface using a steel trowel. Apply sufficient pressure to fill all defects and to feather the product into the subfloor surface.
Put clean water in the mixing container first, and then add the ARDEX FEATHER FINISH®. For best results, mix with an ARDEX T-2 Ring Mixing Paddle and 2” heavy-duty drill. To mix smaller quantities by hand, use 2 parts by volume of powder to 1 part of water. Use a margin trowel and mix vigorously for 2 to 3 minutes.
Beside this, How do you feather a wooden floor?
Likewise, Can you sand feather finish?
The final coat when dry should be sanded as smooth as possible before putting on color or sealant. I would allow 1 day between coats. Ardex Feather Finish dries really fast, but better to give it 24 hours to be sure. … The final coat when dry should be sanded as smooth as possible before putting on color or sealant.
Also, What is feather edge concrete?
feather edge – To smoothly, seamlessly blend the edge of a topping or repair material into the existing concrete.
How long does it take for ardex feather finish to dry?
min. 3 hours
23 Related Question Answers Found
What is feather finish used for?
ARDEX FEATHER FINISH® is an underlayment formulated from a blend of Portland cement and other hydraulic cements that provides a smooth, permanent finish for a variety of substrates prior to the installation of today’s demanding floor coverings, including sheet vinyl and VCT (vinyl composition tile).
What is ardex feather finish used for?
ARDEX FEATHER FINISH® can be used to smooth ridges, fill cracks, gouges, and joints for skim coating to a true featheredge over all types of interior concrete, masonry, wood, terrazzo, and ceramic and quarry tile.
How thick can you apply ardex feather finish?
3mm
What is the top layer of concrete called?
Concrete spalling
Can I hand sand my wood floor?
alleviated with the use of a floor sander. … How to sand a hardwood floor by hand? The exact same way you would with floor sanding machines, but with a lot more elbow grease! Start with a low grit like 40, climb to 60, 80 then 100. Use a handheld orbital sander, ideally with a gear-driven setting.
How can I refinish my hardwood floors without sanding?
– Use a store-bought chemical abrasion kit.
– Buff and recoat floors with polyurethane.
– Use a revitalizer.
How do you feather self leveling compound?
Smooth out and edge the compound with the trowel at once after pouring. Feather edge the compound along the edges of the space. Rub out any trowel marks from poured strips while the compound is still tacky. Use light pressure on the trowel to remove these marks.
Is Henry feather finish the same as ardex?
The Henry Feather Finish is the same stuff as is in this Ardex bag. They are made by the exact same company -just different packaging. DO KNOW THIS – I found the Henry product – the powder before mixing – to be of a much darker gray that the Ardex.
How long does it take for ardex to dry?
Allow thorough drying to a clear, thin film (min. 3 hours, max. 24 hours). NON-POROUS SUBSTRATES: ARDEX FEATHER FINISH will bond to some non-porous substrates, such as burnished concrete, terrazzo, and ceramic and quarry tile, without the use of a primer.
What is feather cement?
® ARDEX FEATHER FINISH® is an underlayment formulated from a blend of Portland cement and other hydraulic cements that provides a smooth, permanent finish for a variety of substrates prior to the installation of today’s demanding floor coverings, including sheet vinyl and VCT (vinyl composition tile).
Can you use ardex feather finish outside?
The product we use and recommend the most is called Feather Finish because it is the most versatile and most difficult to mess up. Having said that, it is not made for every situation and should not be used outdoors or where it will be exposed to non stop moisture.
How can I paint my hardwood floors without sanding?
The best way to refinish wood floors without sanding is to use a technique called screen and recoat. This involves scuffing up the finish with a floor buffer and applying a refresher coat.
Last Updated: 19 days ago – Co-authors : 16 – Users : 6
