Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
(The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.) You should install ice and water protector before other underlayments, including roof felt. Around roof features like dormers and chimneys, you should place ice and water protector below flashing.
Beside this, Do you nail down ice and water shield?
When nails penetrate the ice and water shield on the roof, the rubberized nature of the material creates a gasket effect on the shaft of the nail. Leaks simply don’t happen. Not only does ice and water shield stop leaks caused by ice dams, but it also stops leaks created by fierce wind-driven rain.
Likewise, What goes first drip edge or ice and water?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Also, How do you fasten ice and water shield?
– Cut the membrane into 3-5 m (10-15 ft.) lengths and re-roll loosely. Peel back 300-600 mm (1-2 ft.) …
– Peel the release liner from the membrane. Press the membrane in place with heavy hand pressure.
– Minimum overlap guidelines are set by the manufacturer. GCP requires side laps to be a minimum of 90 mm (3.5 in.)
Can you put felt paper on a wet roof?
Do not shingle over wet or damp roof sheathing or damp felt paper. The trapped moisture cannot evaporate when the sun heats the shingle. … Stripping away the old shingles will cost more, but the new roof covering will last longer if it is a single layer.
24 Related Question Answers Found
Do you overlap ice and water shield?
A single length of WaterGuard Rain & Ice works best, but if that isn’t possible, successive overlaps should be 6″. Firmly hand-roll the laps to ensure a complete, water- tight bond.
Does drip edge go over or under underlayment?
Does Drip Edge Go Over or Under Felt? According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof. But over the underlayment along the rake edges of the roof.
Is roof felt necessary?
Answer: Roofing felt is a layer of tar paper installed beneath the shingles to provide a backup waterproof membrane in case of leakage. Felt, otherwise known as underpayment, is required when asphalt shingles are installed as a first layer of roofing or when they are applied over wood shingles or a built-up roof.Jan 17, 1999
Where do you place the ice and water shield?
Ice and water protector needs to be installed directly onto the roof deck after you have placed the drip edge at the eave. (The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.)
Can you put felt on a wet roof?
Do not shingle over wet or damp roof sheathing or damp felt paper. The trapped moisture cannot evaporate when the sun heats the shingle. If you plan to stay in the home for the next 10 years, do not shingle over older shingles.
Which side of tar paper goes down?
When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper’s two sides are noticeably different. One side is somewhat sticky, though don’t expect it to leave a glue-like residue on your hands. The other side is smooth like paper, and typically contains lettering and line markings.
How much do you overlap tar paper?
Lay roofing tar paper when you have at least one other person to help. Place approximately 5 feet of tar paper at a time. Overlap each piece 2 inches over the piece before it. This ensures a secure barrier against moisture.
Is tar paper water resistant?
Tar paper, also known as Roofing Felt, is both a volatile moisture barricade, as well as the extra protective layer between the plywood and the shingles. … The roofing felt is a compact fiber of wool and is made of condensed fiberglass or polyester fibers. Though Roofing Felt is the protective layer, it can get wet.
Does drip edge go on before ice and water shield?
(The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.) You should install ice and water protector before other underlayments, including roof felt. Around roof features like dormers and chimneys, you should place ice and water protector below flashing.
Is tar paper a good moisture barrier?
At the same time, the sheathing wrap must allow water vapor to pass through so the framing and sheathing can dry to the exterior if it gets wet. Fortunately a number of materials, including traditional asphalt felt (tar paper) have this ability to stop liquid water while remaining “permeable” to water vapor.
Is felt paper waterproof?
Is Roofing Felt Waterproof? Roofing Felt is the support material that is required to develop roll roofing and roof shingles. Being used as the waterproof coverings in commercial as well as residential roofs for decades, these membranes comprise two layers, signifying it is waterproof.
Does underlayment go over ice and water shield?
You should install ice and water protector before other underlayments, including roof felt. Around roof features like dormers and chimneys, you should place ice and water protector below flashing.
Last Updated: 6 days ago – Co-authors : 13 – Users : 10
