There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
Beside this, How often should I tighten my chainsaw chain?
I check my chain for tightness every tank, or more often if needed. You tighten new chains more often until the stretch out. When you’re setting the chain you’ll loosen the nuts and then go for the tensioner. Once you get the chain properly tight, rotate it a quarter rotation around the bar and check/adjust again.
Likewise, Can you put a chainsaw chain on wrong?
Unfortunately the chain will go on either way, but if you put it on backwards, it will not cut. … Remember, when holding the chainsaw, the cutting portion of the blade should be facing away from you, traveling from the back of the chainsaw to the front tip of the chainsaw.
Also, How do I know if my chainsaw chain is too loose?
To determine whether or not your chainsaw’s chain tension needs to be adjusted, pull the chain away from the guide bar a little to see if the drive links remain engaged or not. A loose chainsaw chain will look like the one pictured below when it is pulled away from the guide bar.
How loose should chain be on chainsaw?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
19 Related Question Answers Found
Why does my chainsaw chain keep loosening?
A damaged bar or chain may cause the chain to come loose from the bar and can be very dangerous when operating the machine. The bar has a groove around its outer edge, and the chain has teeth that run slightly inside of the bar rails to keep the chain moving straight.
How do you fix a loose chainsaw chain?
– Step 1: Loosen the Nuts on the Guide Bar Side Panel. This will give the guide bar and chain the room they need to be adjusted. …
– Step 2: Adjust the Tensioning Screw. Tension adjustment screws are located to the side of chainsaw guide bars. …
– Step 3: Tighten the Guide Bar Side Panel Nuts. …
– 16 Comments.
Which way does a chainsaw chain go on a chainsaw?
Chainsaw chains rotate in a clockwise direction, so the cutting edges should be facing away from the engine and to the right, on the top of the chain.
How do you know when your chainsaw chain is worn out?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
How do I know if my chainsaw chain is right?
Chainsaw chain direction, which way should it go? When your Chainsaw bar is on the left of the engine, the chain should rotate counter-clockwise, and the cutting edges should be facing away from the engine.
Why does my chainsaw chain keep stretching?
It is either wear of the links OR the chain expanding due to heat which could be from lack of lubrication if its getting really hot. Otherwise it could be caused by a dull chain, because dull chains also cause the chain to get hot. Wear will happen slowly unless the chain is being abused.
Can you put a chain on a chainsaw backwards?
Unfortunately the chain will go on either way, but if you put it on backwards, it will not cut. … Remember, when holding the chainsaw, the cutting portion of the blade should be facing away from you, traveling from the back of the chainsaw to the front tip of the chainsaw.
Why does my chain keep getting loose?
Your chain might simply be too old or can stretch over time. When this occurs you need to replace it. Consider that your loose chain also may be due to operator error. Exceeding the recommended gear range for the rear derailleur on your bike may lead to a droopy chain when you ride in these gears.
How do I know if my chainsaw chain is backwards?
First thing to check is the drive link, which should be pointing forward. The drive link is the wave-shaped piece that fits into groove on the chainsaw bar. If that little wave is pointing towards the end of the bar (e.g. forward), then your chain is pointed in the correct direction.
Why is my chainsaw chain loose?
This one comes down to physics. When metal gets warmer, it expands. When you’re using your chainsaw, as the chain heats up, it will literally get larger. This is probably the most common reason that a chainsaw will start tight, and then get loose.
Is my chainsaw chain on backwards?
Unfortunately the chain will go on either way, but if you put it on backwards, it will not cut. … Remember, when holding the chainsaw, the cutting portion of the blade should be facing away from you, traveling from the back of the chainsaw to the front tip of the chainsaw.
Are chainsaw chains directional?
The chain of a chainsaw always rotates in a clockwise direction, regardless of type. So you need to make sure the sharp edges of your blades are also facing that direction. They should be pointing away from the motor or body of the chainsaw when on the top side of the chainsaw.
Last Updated: 10 days ago – Co-authors : 15 – Users : 6
