Press and hold Trip/Reset button for two seconds until “Reset for System Check” message appears. Release button. 3. Immediately press and hold button for two more seconds until “Oil 100% Reset if New” message is displayed.
– Turn the ignition to the “RUN” position.
– Press the “SETUP” button to display “OIL LIFE %”.
– Press “RESET” button to display “HOLD RESET IF NEW OIL”.
– Press and hold “RESET” button for more than 2 seconds.
– “OIL CHANGE SET TO 100%” will be displayed.
Beside this, How do you reset the oil change light on a 2008?
– Turn the ignition to run (one position before starting engine). …
– Press the SELECT/RESET button until the engine oil life indicator is displayed. …
– Press the SELECT/RESET button for more than 10 seconds. …
– Press the SELECT/RESET button for more than 5 seconds.
Likewise, How do you reset the oil life on a 2008 Chevy Silverado?
To reset the Oil Life Light on 2007 2008 2009 2010 2011 2013 Chevrolet Silverado, conform to the following instructions: Turn the ignition on without starting the engine. Press the accelerator pedal to the floor three times within five seconds. If the “Change Oil Soon” light flashes, the system is resetting.
Also, Can you reset the oil life percentage?
If your display reads “Engine Oil Life”, select the Reset mode by pressing the Info button on the steering wheel. Then press the Select/Reset button to return your oil life to 100%. If your display reads “Engine Oil Indicator %”, press and hold the Select/Reset knob for more than 5 seconds.
How do you reset the oil light on a Mercury Mountaineer?
Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. Press and hold the RESET control to display “OIL LIFE SET TO 100%”. Your oil life is now reset. Turn the ignition off and then start the engine to verify the indicator has been reset.
23 Related Question Answers Found
How do I get my check engine light to go off?
– 4 Ways to Turn off the “Check Engine” Light. Method. …
– Drive Your Car and Let the Light Go off by Itself. …
– Turn the Car on and off Three Times. …
– Disconnect and Reconnect the Battery. …
– Use an OBD Code Reader.
Is oil life indicator accurate?
The oil life indicator lets a driver know when it’s time for a change, based not only on mileage, but on actual conditions that affect the quality of the oil. … Engineers have figured out a fairly accurate and reliable way to calculate the remaining oil life this way, without having to actually sample the oil.
How do I turn off the oil life indicator?
Press the accelerator pedal down three times in a five-second period. Turn the engine on. If the oil light goes off you have successfully reset the oil light.
At what oil life percentage should you change your oil?
between 40 and 20 percent
How do I get rid of Change engine oil soon?
Hold the Reset Button and Turn the Key Turn the ignition back to the ON position while holding the reset button. Watch the oil change or maintenance light carefully. It should start to blink. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.
What percentage of oil life should I change it?
So your answer is yes, you can wait. Some shops still say 3K or 3 months. That is just a waste. Make sure the monitor is reset every time the oil is changed and I would change it between 40 and 20 percent.
Does disconnecting the battery reset the check engine light?
Leaving the battery disconnected for about 15 minutes will ensure the vehicle systems will completely reset when you reconnect the battery. … Disconnecting the battery will clear the error codes and reset the check engine light.
Can I disconnect my check engine light?
As others have already pointed out, you can simply remove the lamp or disconnect it and it won’t light up. You could use the power line for another lamp that goes on during the startup check but doesn’t normally come on if you want to make sure it does come on during the startup check.
How do I reset my low oil light?
Insert the key into the ignition and turn it to the “on” position without starting the engine. Depress the gas pedal slowly three successive times within 10 seconds. At this point, the system should have reset. You can verify by turning the ignition off and then on again.
Does oil life sensor work?
Rather, it’s a software algorithm that determines when to change your oil. THE OIL LIFE MONITOR DOES NOT CHECK THE OIL LEVEL. … While there is no actual oil sensor, the computer continuously monitors the vehicles’ engine-operating conditions to determine when to change the oil.
Why is my oil light on when it’s full?
If it’s just the oil light and it reads full you may just be due for an oil change. Despite the face the oil is full, the oil still loses viscosity after driving it for so many miles. … It’s also recommended to change the fuel filter every other oil change but even better at every change. Filters don’t cost much anyways.
How do you reset the check engine light?
Insert the key in the ignition, turn the car on for a second, and turn it off for another second. Repeat this process three times. Once you turned your car on/off three times, the check engine light should go away by itself.
Last Updated: 6 days ago – Co-authors : 10 – Users : 7
