A 14″ or 12″ spacing will provide a lot more support for the soffit to reduce sagging between fasteners. There will always be some slight bit of sag though which is unavoidable with vinyl but if installed properly it’s not bad.
16 to 24 inches
Beside this, Does vinyl soffit expand?
Once a soffit panel is face-nailed, it will expand only in one direction—in this case, toward the receiving channel. Be sure to leave space for the full expansion allowance in the receiving channel.
Likewise, What length does vinyl soffit come in?
Standard sidings are usually 12′ to 12-1/2′ long. With standard siding panels, seams appear every two to three feet. Longer length sidings are typically offered in 16’8”, 20′ and 25′ ranges.
Also, Can you overlap vinyl soffit?
No, you can’t overlap it successfully, so you will be relegated to using some sort of joint channel. I may have said “no” too emphatically. You can always try it to see what sort of continuation you get end to end, but it may look neater with the channel.
Can you put new soffit over old?
If the existing wood is in good shape, then it is safe to cover it with aluminum or vinyl material. … In simple terms, it is not necessary to remove the old soffits as long as they are in good shape and proper allowance is made for air circulation and ventilation.
25 Related Question Answers Found
How far should you overlap vinyl siding?
Always refer to the installation guide on the particular vinyl siding that you’re installing, but most vinyl siding panels should overlap each other by at least an inch. Add 3/8 in.
How much do you stagger vinyl siding?
Always refer to the installation guide on the particular vinyl siding that you’re installing, but most vinyl siding panels should overlap each other by at least an inch. Add 3/8 in. on hot days because the siding will contract when the temperature drops.
Is vinyl soffit better than aluminum?
Vinyl also has a higher impact resistance than aluminum which adds to its durability. When used under eaves, it helps to improve insulation. Less energy is utilized to heat and cool the house which brings down your energy costs with time. Vinyl soffit is low maintenance yet it keeps in good shape for a long time.
How do you redo soffits?
– Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. …
– Remove Rotted Fascia. Remove the rotted section of fascia. …
– Remove Old Soffit. Pull down to remove the old soffit. …
– Remove Rotted Rafter. …
– Attach Cleat. …
– Attach New Rafter. …
– Seal Replacement Soffit. …
– Attach Replacement Soffit.
What is the best material to use for fascia board?
– The most common choice due to its affordability.
– Primarily constructed from either spruce, pine, or fir.
– Because it is not water-resistant, wood is subject to rot.
– Must be primed and painted regularly to extend longevity.
How do you join vinyl soffit?
Insert the first piece of soffit into the “J” channel on the ceiling. Push it all the way to the edge, leaving approximately ¼-inch of clearance. Secure the piece by driving roofing nails through the nail slots in the soffit to the ceiling or furring strips underneath. Nail every 12 to 16 inches.
How do you fix sagging soffits?
– Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. …
– Remove Rotted Fascia. Remove the rotted section of fascia. …
– Remove Old Soffit. Pull down to remove the old soffit. …
– Remove Rotted Rafter. …
– Attach Cleat. …
– Attach New Rafter. …
– Seal Replacement Soffit. …
– Attach Replacement Soffit.
How much does it cost to replace soffits?
Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.
What is the average cost to install vinyl soffit?
The national average materials cost to install a vinyl soffit is $1.56 per linear foot, with a range between $1.24 to $1.88. The total price for labor and materials per linear foot is $6.46, coming in between $4.82 to $8.11. A typical 25 linear foot project costs $161.62, with a range of $120.46 to $202.77.
What length does soffit come in?
Panels come in 12-foot lengths that are either 12 or 16 inches wide. Therefore, a panel that is 12 inches wide equates to 12 square feet, and a panel that is 16 inches wide equates to 16 square feet. Plan on purchasing enough soffit to cover about 5 percent more space than necessary to account for waste and overlaps.
How do you overlap vinyl fascia?
What timber do you use for fascia boards?
Cedar is a popular fascia wood and redwood is another. That’s because both species resist rot and moisture very well, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive. You construct fascia boards out of 1-inch lumber.
Last Updated: 14 days ago – Co-authors : 6 – Users : 5