One major difference if you do your research online is that Redgard is certified for use in steam rooms and as a vapor barrier whereas Hydro-ban is not. Both have the certification for pan liners and waterproofing, but Redgard outperforms Kerdi membrane (not Kerdi DS) in Perms of vapor penetration.
Mapelastic AquaDefense is a premixed, advanced liquid-rubber, extremely quick-drying waterproofing and crack-isolation membrane for installation under ceramic tile or stone in residential, commercial and industrial environments.
Beside this, How do you use Aqua defense in the shower?
Likewise, Can you paint over AquaDefense?
since you are not installing tile over it, it can be painted with a latex paint.
Also, How long does it take for Aqua defense to dry?
about 30 to 50 minutes
How do you use Aqua defense?
16 Related Question Answers Found
Can you tile over AquaDefense?
How soon can I install tile over Mapelastic AquaDefense? Cement-based thin-sets – such as MAPEI’s Ceramic Tile Mortar, Ultraflex 1, Porcelain Tile Mortar and Ultraflex 2 – can be installed when Mapelastic AquaDefense turns to a dark green color (typically after 30 to 50 minutes).
Is one coat of Redgard enough?
For tile installations bonding directly to the substrate; strongly recommended to apply at least one full coat of “undiluted” RedGard® to the “dry” primed area and allow to dry completely before tile installation work is to begin.
Can you use AquaDefense on drywall?
No. AquaDefense is not approved for showers constructed with drywall.
How do you use AquaDefense?
Apply Mapelastic AquaDefense with brush around and up onto floor or wall penetration. Let dry to a dark-green color. 3. Apply a second coat and let dry.
Can AquaDefense be painted?
Mapelastic AquaDefense can be applied with a paint brush or 3/8″ nap paint roller.
Can you paint over a waterproof membrane?
As long as you use a good primer, you should be OK, though. You can apply thinset over the RedGard and prime and paint over that. Joint compound is reactivated when it absorbs water and can cause problems like mold and blistering or delamination of paint film.
Can you use Redgard on drywall?
It’s true that RedGard can be used on drywall, but when all their product information is carefully considered, it is not the case that RedGard can be used on Drywall in a wet area.
How do you waterproof a drywall shower?
The best way to waterproof your drywall is to use a waterproofing primer. You can find both oil- and latex-based waterproofing primers made by most paint manufacturers. These products are created specifically to prevent mold and mildew on the surface to which they are applied.
Is redguard good for shower walls?
RedGard Creates a Waterproof and Crack Resistant Membrane If you can paint a wall you can use RedGard no problem. And for this shower we only needed one gallon. There are two ways to get RedGard on cement board panels: Roll it on the wall with a 3/4 inch nap roller.
Can you use AquaDefense on plywood?
Ready to use, flexible, ultra rapid drying waterproofing membrane for interior and exterior use in showers, wet rooms and on balconies*. Can be tiled after 4 hours. For use on screed, render, concrete, plywood and ceramic finishes.
Will Thinset stick to AquaDefense?
Aquadefense is a great waterproofing product. Thinset mortar will adhere to it … that’s what it’s specifically manufactured for. It requires the use of a polymer modified / latex modified thinset mortar. Check out the library shower construction thread to make sure that you built your shower correctly so far.
Will Thinset stick to RedGard?
You”ll be fine with thinset over Redguard on walls. It’s recommended for waterproofing niches, shelves, and entire shower walls when tar paper or poly are not used as a vapor barrier behind the CBU.
Last Updated: 16 days ago – Co-authors : 10 – Users : 5
