What’s the difference between r6 and r8 flex duct?


The thickness in the ducting materials used to make R6 and R8 ducting is one of the glaring differences between the two. R8 ducting uses thicker insulation than R6 ducting. This means that if you were to do air conditioning installation using R8 ducting, you get better insulation than if you are using R6 ducting.

No. Avoid flexible duct for your range hood, regardless of the CFM. Flexible duct is a poor investment because it is: Not durable/sturdy.

Read the full answer

Moreover, Does a range hood have to be vented outside?

Do range hoods have to be vented outside? No; range hoods without a duct, or ductless range hoods, can recirculate air back into your kitchen. However, to clean your kitchen air most efficiently, purchase a ducted range hood. Rather than relocate the cooking exhaust, it will evacuate it from your home entirely.

Secondly, What is the best insulation for ductwork?


Simply so, Should range hood vent pipes be insulated?

Like other duct systems in the home, insulation around range hood ducts reduces nuisance noise and vibration when the fan inside the vent hood is running. But more importantly, insulating duct work wherever ducts run through unheated parts of the home will help prevent air loss through the thin metal ducts.

How do you seal a range hood duct?

Seal holes in the fan housing with caulk, sealing putty, or metal tape. Install the fan then seal around the fan with caulk or canned spray foam. Seal the exhaust duct to the fan box with approved metal tape or mastic. Seal around the exterior fan duct vent with caulk or a pre-made exterior wall gasket.

24 Related Question Answers Found


How does a non vented range hood work?

A ductless (or ventless) range hood does not vent out of the home, instead, it carries the debris and smoke form the air and filters it through a charcoal or carbon filter before releasing it back into the room. While many times this method is not as functional as a vented hood, it does work.

Where do you put a backdraft damper on a range hood?

Range Hood Damper Location However, if you’re concerned more about backdrafting, install your damper close to the interior wall, where your range hood connects to the ductwork.

How much does flex duct cost?

Flexible ducting with built-in 3 insulation typically costs $1.30-$2.50 per linear foot.

Can you vent a range hood through a wall?

A ducted hood can be installed through your cabinetry, ceiling, or straight through the wall behind the hood. The vent exhausts outside either to an exterior wall or the rooftop. Ducted range hoods are common in commercial kitchens, homes with gas stovetops, or higher-end homes.

How do you vent a range hood on an interior wall?

– Step 1: Disband the New Range Hood.
– Step 2: Open a Hole.
– Step 3: Put in the Rubric.
– Step 4: Procedure for Installation.
– Step 5: Restore Electricity.

Does Flex duct reduce airflow?

Friction is the enemy of airflow. Unlike rigid ducts, which are cut to length within a tolerance of 1 inch or less, it’s easy to cut a length of flexible duct that’s several feet longer than is needed to get from point A to point B [2A]. That creates slack in the duct, which reduces airflow for two reasons.

Do I need a backdraft damper?

Backdraft dampers allow air to efficiently flow through exhaust ducts to the outside, yet prevent the unwanted flow of air into a house when the exhaust fans are off. They stop cold air from coming in, allowing a more comfortable temperature in your home.

Do I need a vented range hood?

Without question. It’s far preferable to vent the air outdoors than to recirculate it into the room. A vented hood that removes steam, smoke, heat, and cooking odors is the best way to keep your kitchen clean, since it gets rid of grease particles that would otherwise accumulate on your walls and cabinets.

Can you spray foam insulation on ductwork?

Metal, flex, or fiber board ducts can be used. Once these preparations are made, the ducts can be encapsulated in at least 1.5 inches of closed-cell polyurethane spray foam. Encapsulating the ducts in spray foam increases the R-value of the ductwork and reduces air leakage.

How thick is r6 duct insulation?


How do you vent a range without a hood?

– Use a window fan.
– Use a portable HEPA air filter.
– Use a fan in another room, like the bathroom.
– Get a grease splatter guard.
– Wipe down your kitchen cabinets frequently.
– If you paint your kitchen, use a satin or semi-gloss finish, or choose scrubbable paint.

How do you seal old vents?

Watch the video

Last Updated: 11 days ago – Co-authors : 15 – Users : 6


Please enter your answer!
Please enter your name here