When lit, this red light, also called a lockout light, indicates that a safety mechanism on your furnace has caused a shutdown because it has detected a problem or recognized a fault. (Note: Not all furnaces have this red light. Some have a red reset button that does not light up.)Feb 22, 2018
A blinking red light on a Trane furnace can mean numerous things, depending on the speed of the blinking and the number of times that the light blinks. Continuous (slow or fast) flashing indicates that your furnace is on and either calling (fast) or not calling (slow) for heat.
Beside this, How do I reset my Trane furnace?
Likewise, How do you read a furnace error code?
Also, Where is the pilot light on Trane furnace?
Trane pilot light tubes are found toward the rear of the chamber, below the furnace burner coil, with the brass tip pointed upward at a slight angle.
How do you light the pilot on a Trane?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
23 Related Question Answers Found
What does a red blinking light on a Trane furnace mean?
A blinking red light on a Trane furnace can mean numerous things, depending on the speed of the blinking and the number of times that the light blinks. Continuous (slow or fast) flashing indicates that your furnace is on and either calling (fast) or not calling (slow) for heat.
How do I reset my Trane thermostat to factory settings?
– Shut Down Your AC at the Thermostat. …
– Find Your Circuit Breaker Box. …
– Reset the Circuit Breaker for Your AC Unit. …
– Wait 30 Seconds. …
– Turn the AC Thermostat Back On. …
– Call Vredevoogd Heating & Cooling for all your Furnace & AC needs.
Should my furnace light be blinking?
Answer: There should be a light on the circuit board blinking to tell you roughly where to look for the problem. Since the blower is kicking on immediately, something has failed. Maybe the board or inducer motor since it’s happening before the unit even tries to light.
Can I relight the pilot light by myself?
Pilot lights were once standard on all gas furnaces, but newer systems don’t always contain pilot light ignition systems. Instead, some newer furnaces use electronic ignition systems. … Often, homeowners can relight the pilot themselves.
Where is the reset button on my Trane furnace?
After the furnace cools, access the blower motor compartment. The compartment usually sits at the very bottom of the appliance. If you look inside the blower motor fan, you should find the reset button. Look for a small red or yellow button on the side of the blower motor.
How do I turn the pilot light on?
Press and hold the valve while you turn it to “Pilot.” Use a long BBQ lighter to relight the pilot light. Keep the valve pressed in for at least five seconds to make sure the pilot light remains lit. If the pilot light stays lit, turn the valve to “On.” If it doesn’t stay lit, repeat these steps.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How do I reset my furnace lockout?
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.
How do you reset a furnace safety switch?
– Locate your furnace’s heating duct. …
– Locate the white limit switch. …
– Look at each arm to identify the settings. …
– Identify the component (setting) located in between the two arms. …
– Set the temperature on the middle component to approximately 105 to 115 degrees Fahrenheit.
Why is yellow light flashing on my furnace?
What it means: If you’re wondering, “What does the yellow light on my Carrier furnace mean?” it signifies that the furnace is stuck in high-fire mode. The high-fire mode should only operate for short periods of time to heat a very cold house faster.
Is it dangerous to relight a pilot light?
A pilot light may need to be re-lit from time to time after being extinguished on purpose or by accident. If it is accidentally extinguished, there exists a danger that the gas used to keep the flame lit will continue to vent, possibly into the living space.
What do you do when your pilot light goes out?
– Turn off your appliance at the power switch or thermostat.
– Find the gas valve control knob and turn it to select “pilot.”
– If pilot light controls are sticky, do not apply force or use oil. …
– Press the red button while simultaneously holding a match to the pilot burner.
Last Updated: 9 days ago – Co-authors : 4 – Users : 11