A pump performance curve indicates how a pump will perform in regards to pressure head and flow. A curve is defined for a specific operating speed (rpm) and a specific inlet/outlet diameter. The curve also shows the shut off head or the head that the pump would generate if operating against a closed valve.
The performance curve of a reciprocating pump differs from that of a centrifugal pump. Closing the discharge valve increases the pressure but does not change the flow. Reciprocating pumps run at a much lower speed than Centrifugal pumps.
Moreover, What is the operating point of a pump?
The operating point of the system “pump / network” is the flow rate that balances the pressure supplied by the pump and pressure necessary for the operation of the network flow.
Secondly, How do you find the operating point of a pump?
– Measure total dynamic head. Total dynamic head (TDH) is total head developed across the pump centerline reference for a given set of conditions (pump speed, impeller diameter, etc.).
– Measure motor/driver load BHP.
– Process instrumentation and process mass balance calculations.
– Tank volume changes.
– Other operating data.
Simply so, What is the duty point of a pump?
Pump operating point or duty point is the intersection of pump characteristic and piping system characteristic. The pump will always operate where the system and pump curves intersect. At that point, there is a balance between what the system demands and what the pump can deliver.
What is performance curve of a pump?
A pump performance curve indicates how a pump will perform in regards to pressure head and flow. A curve is defined for a specific operating speed (rpm) and a specific inlet/outlet diameter. The curve also shows the shut off head or the head that the pump would generate if operating against a closed valve.
15 Related Question Answers Found
Do positive displacement pumps have curves?
Positive displacement (PD) pump technologies vary, as do the curves for these pumps. A person without significant exposure to pump selection is often experienced only with centrifugal pump curves. Therefore, it can be frustrating to get the data required from a positive displacement curve.
How is the operating point of a pump and piping system determined?
The point at which a pump operates in a given piping system depends on the flow rate and head loss of that system. By graphing a system characteristic curve and the pump characteristic curve on the same coordinate system, the point at which the pump must operate is identified.
How do you use a pump curve?
What type of flow does the reciprocating pump have?
pulsed output
What is a positive displacement pump used for?
Positive Displacement pumps are commonly used for pumping high viscosity fluids such as oil, paints, resins or foodstuffs. They are preferred in any application where accurate dosing or high pressure output is required.
Where do we use reciprocating pump?
Incorporating reciprocating pumps results in repeatable and precise mechanical operations. Industries that commonly use reciprocating pumps include: Oil and gas: Oil and gas industry applications include disposal, offshore oil, production, injection, feed, charge, steam generators, mainline, and field gathering.
What is an example of a positive displacement pump?
The best positive displacement pump examples are piston, plunger, diaphragm, gear, lob, screw and vane. Piston and Plunger pumps are used to pump low viscosity fluids, paint spraying, oil production, and high force washing. Vane pump is used in low viscosity liquids, fuel loading, & transmission, etc.
What does a pump curve tell you?
A pump performance curve indicates how a pump will perform in regards to pressure head and flow. A curve is defined for a specific operating speed (rpm) and a specific inlet/outlet diameter. The curve also shows the shut off head or the head that the pump would generate if operating against a closed valve.
What does the best operating point represent?
The Best Efficiency Point is defined as the flow at which the pump operates at the highest or optimum efficiency for a given impeller diameter. When we operate a pump at flows greater than or less than the flow designated by the BEP, we call this “operating pumps away from the Best Efficiency Point”.
What is a duty point?
Pump operating point or duty point is the intersection of pump characteristic and piping system characteristic. The pump will always operate where the system and pump curves intersect. At that point, there is a balance between what the system demands and what the pump can deliver.
What is the pump curve?
The primary selection tool is called a pump curve. Pump curves are essentially data about a given pump’s ability to produce flow against certain head. When you’re reading a curve, the pump’s flow rate will be on the top and bottom and its height to push is on the sides.
How do you calculate system curve of a pump?
Last Updated: 8 days ago – Co-authors : 9 – Users : 4
