PopularAsk.net – Your Daily Dose of Knowledge

What does FL Lo mean on Maytag washer?

not detecting

Read the full answer

error code

Beside this, How do you fix the LF code on a Whirlpool Cabrio washer?

– Make sure the water supply to the washer is turned on and has pressure.
– Check the screens on the water supply lines and the water inlet valve for blockage.
– Make sure the washer is not filling and draining at the same time, if so check your drain hose and insure that its’ not vapor locked.

Likewise, What does it mean when a washing machine says LF?

too long to fill

Also, What does Fl mean on a washer?

Code Meaning
—- ————————————————————————
FL The washer failed to lock the door.
Hr Washer temperature control problem.
LE The washer has tried to fill but has not reached the proper water level.
LO The door will not unlock.

How do you fix the LF code on a Whirlpool Cabrio?

– Make sure the water supply to the washer is turned on and has pressure.
– Check the screens on the water supply lines and the water inlet valve for blockage.
– Make sure the washer is not filling and draining at the same time, if so check your drain hose and insure that its’ not vapor locked.


15 Related Question Answers Found

 

What does Fl mean on Whirlpool washer?

F8 E1 or LF or LO FL Error Code in the Display of my Whirlpool Washer. Error Code F8 E1, LF, or LO FL all indicate that no water is detected entering washer after 13 minutes.

What does FL Lo mean on a Whirlpool washer?

error code

What does Fl mean on Maytag washer?

faulty door lock solenoid

How do I reset my Whirlpool washer?

– Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
– The motor has now been reset and is ready for you to start a cycle.

How do I clear the error code on my Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do you clear the codes on a Whirlpool Cabrio washer?

Try the Cabrio Reset Procedure Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.

How do I reset my Maytag front load washer?

– Press the “Power/Cancel” button.
– Push the appropriate button to choose a new cycle.
– Press “Start/Pause.” You have now reset your Maytag washer.

How do you clear the LF code on a Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do you clear the codes on a Whirlpool Cabrio?

Touch any button on the display pad to clear the error code or press “Pause/ Cancel.” Choose another cycle and press “Start”. Disconnect the Cabrio from power if the error or problem comes back. Wait 5 minutes before restoring power.

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I fix error code F02?

Press the pause or cancel button on the Whirlpool washing machine to clear the F02 error code from the display, and try using it again. The error code is displayed when the washer takes more than eight minutes to drain, but may just be a glitch.

How do you reset a front load washer?

– Press POWER to turn the washer off.
– Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
– With the power disabled, press and hold the START/PAUSE button for 5 seconds.
– Plug the washer back in, or turn the circuit breaker back on.


Last Updated: 6 days ago – Co-authors : 15 – Users : 10

Exit mobile version