washer control detected
The F02 error code on a Whirlpool washer indicates that the control detects a long drain time. This can be caused by excessive suds in the tub, a restriction or clog in the drain system or by a number of other component failures.
Beside this, How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Likewise, What does F 01 mean on a washing machine?
failed electronic machine control board
Also, How do I fix the f20 code on a Whirlpool washer?
Turn off the water and remove inlet hoses from the inlet valves in the back of the washer. Inside the inlet valves are screens. Remove any accumulated film or particles from the screens. Reinstall hoses, turn on water, and check for leaks.
How do you fix the F code on a Whirlpool Cabrio washer?
– Unplug the washing machine for 2 minutes and then plug it back (it will help the appliance re-conduct self-diagnostics and conclude that there is no breakdown);
– Press the START and PAUSE buttons simultaneously and hold them for 1 minute to clear the error code.
21 Related Question Answers Found
How do I reset my washing machine?
– Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
– The motor has now been reset and is ready for you to start a cycle.
What does Code F mean on Whirlpool Cabrio washer?
door lock error
How do I put my Whirlpool washer in diagnostic mode?
Press the 1st button you used to enter the Duet Diagnostics Mode. Now that you are in the Duet washer interface test you can press each button one time. when a button is pressed the button’s indicator light should turn on and you should get a beep.
What does F mean on a washer?
component problem
How do you check the pressure switch on a Whirlpool Duet washer?
– Unplug the Whirlpool Duet washer power cord from the wall outlet. …
– Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver. …
– Locate the pressure switch inside the washer cabinet. …
– Adjust the scale on your ohmmeter to the RX1 or X1 scale.
What does F1 mean on a Cabrio washer?
The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose.
How do you clear the error code on a Whirlpool Duet washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you reset a Whirlpool washing machine?
– Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
– The motor has now been reset and is ready for you to start a cycle.
Is there a way to reset a Whirlpool washer?
How do you reset a Whirlpool washing machine? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
What does F mean on Whirlpool washer?
door lock error
How do I fix error code F02?
Press the pause or cancel button on the Whirlpool washing machine to clear the F02 error code from the display, and try using it again. The error code is displayed when the washer takes more than eight minutes to drain, but may just be a glitch.
What does fo1 mean on washing machine?
failed electronic machine control board
Last Updated: 6 days ago – Co-authors : 11 – Users : 9
