As a general rule, a shower curb foundation is 3 to 4 inches thick and 4 to 6 inches tall, with finish material adding to these dimensions.
The shower pan base mortar layer should be about an inch thick. The shower floor already has a pre-slope, so just apply a base mortar layer that is even thickness throughout the shower floor area.
Beside this, How thick should a shower base be?
2-3 inches
Likewise, How thick should shower floor mud bed?
If you are installing tile, the mortar bed should be 2-3 inches thick on the outer edge and slightly less at the drain. When mixing the mortar use only enough water to obtain a “dry pack” consistency.
Also, How thick should shower pan be?
Start with a 1/4-inch thick layer around the shower drain and then slope upwards and outwards from there to the perimeter. Commercial specifications are 1/4-inch of slope for every linear foot.
How thick should a shower pre slope be?
Your finished floor (after your liner and top mud bed are installed) needs to be 1″ to 1 1/4″ thick at the drain. So, if we make the pre-slope 3/4″ thick at the drain it needs to be a total of 1 1/2 inch thick at all your walls.
24 Related Question Answers Found
How thick should a mud floor be?
Firmly tamp and screed the FLOOR MUD. The thickness should be between 3/4″ and 1-1/4″ (19.1 and 31.8 mm). A minimum of 1-1/4″ (31.8 mm) thickness is required for shower receptors. Shower stall areas also require a suitable waterproofing membrane and reinforcement.
Is a shower pre slope necessary?
One of the most important preparation steps is to pre-slope a shower. … A pre-slope is necessary because once water has reached there, it needs to be directed to the drain area. If underneath your liner is flat – without any slope to the drain – this will cause water build-up, eventually causing mildew.
What kind of mud do you use for a shower pan?
QUIKRETE
How thick should my mortar bed be?
The terms thinset cement, thinset mortar, dryset mortar, and drybond mortar are synonymous. This type of cement is designed to adhere well in a thin layer – typically not greater than 3/16th thick. For example, a 3/8″ notch trowel will produce a 3/16th inch thick coating after the tiles are pressed in to the cement.
What do you use to pre slope a shower?
Do I need tar paper under shower pan?
Tar paper helps to prevent the sub floor from absorbing moisture from the pre-pan mix that will go on top of it.
What happens if mortar is too thick?
What happens if Thinset is too thick? The most likely dangers of using it too thick are cracks (see photo), delamination, and lippage. Please note that the thinset being shown as a patch in the previous pictures is one designed to be used on plywood (an ANSI A118. 11 mortar).
Is Pre pitch necessary?
Why do I need to use Pre-Pitch? Pre-Pitch produces a properly pitched sub-floor UNDERNEATH the pan liner to direct water towards the drain’s weep holes. This eliminates the ponding of water between the liner and the mud bed inside the liner, this will help eliminate mold and bacteria growth.
What is a mud set shower?
A mud set showers starts with metal lathe which is interwoven and stapled to the studs. It then receives two coats of cement by hand with the second coat being skimmed flat and plumb. … With mud set, this is not a problem because we have the ability to “float out” any inconsistencies while applying the cement.
What is the best mortar for shower pan?
The ideal mortar for a shower pan is a mix of standard cement mix with sand and Portland cement. This type of mortar creates a great water-resistant barrier that can support the weight of the shower unit.
How do you make a mud shower pan?
Do you need a pre slope in a shower?
No. I’ve installed a number of showers. There is no such thing as a ‘single step’ process. If you don’t have a pre-slope, or use something like Schluter’s drain pans (which is what I always use now), the water will pool and just sit there which will cause bacteria growth, possibly mold, etc.
Last Updated: 18 days ago – Co-authors : 16 – Users : 11