- Furnace Blower Motor Replacement Cost On average nationwide, a furnace blower motor replacement costs $400 to $600, including parts and labor.
- A single-speed blower motor costs around $450 to replace while a variable-speed motor costs $600 or more.
- You’ll also need to budget labor, about $75 to $125 per hour.
Subsequently, What causes a furnace motor to burn out? Inadequate air flow within the system. Buildup of dust, dirt, or debris. Electrical problems, including an excessive voltage supply. Motor insulation failing prematurely due to high temperatures.
What causes blower motor failure? Blower motor breakdown can be the result of anything from old age to failed bearings, high amp draw, electrical failure in the windings, dirt accumulation, and more. “The most common cause is dirt accumulation due to lack of maintenance,” said Tom Beaulieu, president of Bay Area Services Inc.
Yet, What causes a furnace blower to stop working? To figure out if the blower motor belt is damaged, turn off the furnace at the circuit breaker panel in your home. Next, head back to the furnace and inspect the belt that runs the blower. When the fan in a furnace is not working, this is an indicator of a worn down or cracked belt that needs to be replaced.
How long does it take to replace a motor blower? How long does it take to replace a blower motor? Replacing a blower motor takes 2 to 3 hours on average. The blower motor is typically located behind a control board and other furnace parts.
Can you run furnace without blower?
The blower fan motor The furnace can produce heat inside the combustion chamber—but that heat won’t go anywhere if the blower fan isn’t running. Because there’s a danger of the furnace overheating without the blower fan, the furnace won’t operate unless the blower has power.
How long does it take to replace a blower motor?
How long does it take to replace a blower motor? Replacing a blower motor takes 2 to 3 hours on average. The blower motor is typically located behind a control board and other furnace parts.
Where is the reset button on furnace blower motor?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do you diagnose a blower motor problem?
You might also hear ongoing whirring noises, or noises that change or get louder if you increase the fan speed. These are all signs of problems with the blower motor. In some cases, you may even notice smoke or smells of burning while driving, in which case you should pull over immediately.
Where is furnace blower reset button?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do I reset my blower motor?
How to Find and Reset your Furnace Motor Blower
- Step 1: Turn off the power to the furnace. …
- Step 2: Remove the blower compartment cover. …
- Step 3: Make sure the blower is completely cooled off. …
- Step 4: Locate the reset button. …
- Step 5: Press the button in (assuming that this is your issue and that the button has popped).
Is it hard to replace a blower motor?
The replacement of the blower motor is common and straightforward, so most shops will perform the repair — many on the same day.
What can cause a furnace blower motor to stop working?
Make sure that the power cord hasn’t melted or a fuse hasn’t been blown. If your cables are looking fine, try unplugging the fan for a few minutes and then plugging it back in again. Sometimes, this process can reset the motor and solve your furnace problems.
Where is the blower motor located in a furnace?
One of the hardest-working parts of your home’s furnace is the blower motor. In a gas forced air furnace, it’s located in a box at the base of the furnace next to the air filter, where it draws return air through the filter.
What is the difference between a fan motor and a blower motor?
What Is a Blower Motor? Unlike the condenser fan motor, the blower motor is located indoors. It’s the component that blows cool air through the ducts and into different parts of your home. So it’s essentially your air mover.
Will a furnace work without a blower?
The blower fan motor The furnace can produce heat inside the combustion chamber—but that heat won’t go anywhere if the blower fan isn’t running. Because there’s a danger of the furnace overheating without the blower fan, the furnace won’t operate unless the blower has power.
What happens when your blower motor goes out?
WEAK AIRFLOW OF THE BLOWER MOTOR The fans will work at certain speeds until they stop working altogether. Such a fault not only results in poor airflow but also decreases the efficiency of the defroster as it uses the same fan to blow air at the windshield.
How do you reset furnace blower?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do I test my furnace blower?
Should I replace my blower motor?
In general, if your furnace is less than 12 years old, replacing your blower motor is probably the best choice, especially if you’ve kept your furnace on an annual inspection and maintenance schedule. Keeping your furnace well maintained will keep it performing well and help prevent component failures.