Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.
– Washer will not stop when the lid is open. “When you open the lid the washing machine will not stop what it’s doing.”
– Bad lid switch. …
– Water will not drain out of the washer. …
– Clogged waste hose. …
– Bad drain pump. …
– Bad pump motor. …
– Washer does not spin/agitate. …
– Broken drive belt.
Moreover, How do you run a diagnostic on a Kenmore washer?
Secondly, How do you run a diagnostic test on a Kenmore he2 plus washer?
Simply so, How do you reset a Kenmore washing machine?
– Press the “Stop” button twice, and then press the “Power” button.
– Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
– Press the “Start” button to complete the reset process and restart the washing machine.
How do you reset the code on a Kenmore washing machine?
– Press the “Stop” button twice, and then press the “Power” button.
– Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
– Press the “Start” button to complete the reset process and restart the washing machine.
28 Related Question Answers Found
What size is a Kenmore 70 Series washer?
Size. The Kenmore 70 Series Washer has a width of 27 3/4-inches and a height of 43 1/8-inches.
What year is a Kenmore 70 Series washer?
2001
How do you check a Kenmore washer motor?
Remove the violet and tan wires from the water level switch and join (jump) them together to bypass the water level switch and see if the washer will agitate. If the washer will agitate then most likely the motor is okay.
Why is my Kenmore washer not working?
If Kenmore Washer Won’t Drain, Check: The drain pump or drain hose can become blocked by debris. If you find obstructions be sure to clean the pump and the hose to make sure they are free of clogs. While you have the drain hose off make sure it’s not damaged in any way. If you find damage replace the hose.
How do you reset a Kenmore washer model 110?
How do I know if my washer motor coupler is bad?
If the washer fills to the selected level and you hear the motor running but the washer is not agitating, set the dial on the spin cycle. If the washer drains the water and you hear the motor running (making noise but not spinning), it is likely you have a broken motor coupler.
How do you fix a washing machine coupler?
How do I know if my Splutch is bad?
– The Clutch Feels Like It Is Slipping.
– The Transmission “Grinds” When Shifting.
– The Transmission Will Not Go Into Gear.
– The Clutch Pedal Just Feels Odd.
How do I find out what year my Kenmore washer is?
Locate the serial number on a Kenmore washer made by Whirlpool. The second letter of the serial number identifies the year the machine was manufactured. For instance, “L” represents 2001, “M” means 2002 and, continuing through the alphabet, “Y” means 2009.
How do I reset my Kenmore he2 washer?
Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display. Start a short cycle, to check operation of the appliance, by selecting a cycle and pressing and holding the start button until the appliance starts.
How do you run a diagnostic test on a Kenmore he3t washer?
– With the washer empty, close the door.
– Push “control/on” or “Start”
– Select “Drain/Spin”
– Select “No Spin” by pressing SPIN SPEED touchpad.
– Push “PREWASH” option four times within 5 seconds.
– C:00 should light up and begin the diagnostic.
How do you put a washing machine in self test diagnostic mode?
Last Updated: 11 days ago – Co-authors : 10 – Users : 6