– Perform a Master Reset. Unplug your washer for about one minute. …
– Test the Lid Switch Assembly. …
– See if the Drain Hose is Kinked. …
– Check the Drain Hose or Pump for Clogs. …
– Clean out the Coin Trap. …
– Check the Water Level Control. …
– Schedule Washing Machine Repair.
water drain issue
Beside this, Why is my Whirlpool washer not draining or spinning?
The Drain Pump May be Clogged or Defective If the hose and filter are both okay, you’ll need to check the drain pump. It may be clogged with debris or could be defective and needs to be replaced. To check this you will need to disconnect the drain hose, and remove the back panel from your Whirlpool washer.
Likewise, Why won’t my Whirlpool washer spin and drain?
If the hose and filter are both okay, you’ll need to check the drain pump. It may be clogged with debris or could be defective and needs to be replaced. To check this you will need to disconnect the drain hose, and remove the back panel from your Whirlpool washer.
Also, How do I clear my F21 code on my Maytag washer?
– Unplug the washer for two minutes to reset the machine.
– Once the code is removed, restart the cycle by pressing the POWER button one time.
What causes a washing machine to not drain completely?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
24 Related Question Answers Found
What does F21 mean on my Maytag washer?
drain times
Why are my clothes still wet after spinning?
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. … Often with this issue, whatever is causing it to not drain during the spin cycle means the water isn’t draining off fast enough and is essentially flowing back into the washer drum, re-soaking your clothing.
How do I know if my shift actuator is bad?
When the actuator fails there is usually and awful lot of grinding noise, and the tub and agitator operate at a slow speed, if at all. In most models, you will have an F7 -E1 or E5 error code in the display.
Why is my front load washer not draining completely?
A washing machine not draining is one of the most common problems we encounter. It can be caused by one of the following: – The drain hose or pump is clogged with a small item of clothing, residual gunk or other debris. – The washer is malfunctioning and not engaging the drain/spin cycle properly.
What causes a washer to not spin out all the water?
If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I get the water out of my washing machine that won’t drain?
– Perform a Master Reset. Unplug your washer for about one minute. …
– Test the Lid Switch Assembly. …
– See if the Drain Hose is Kinked. …
– Check the Drain Hose or Pump for Clogs. …
– Clean out the Coin Trap. …
– Check the Water Level Control. …
– Schedule Washing Machine Repair.
Does Spin Cycle drain water?
It removes the water from the tub during the spin cycle. The washer pump forces water from the bottom of the machine into the drain hose. … When the water reaches the bend in the hose, it goes out of the drain.
How do you get standing water out of a washing machine?
– Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. …
– Step 2: See If You Can Drain the Drain Hose. …
– Step 3: Check Out the Drain Pump. …
– Step 4: Drain the Interior Manually If Needed. …
– Step 5: Know When to Call a Professional.
How do I clear a clogged washing machine drain?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
How do I put my Maytag washer in diagnostic mode?
Can you fix an unbalanced washing machine?
Redistributing The Washing Machine If four towels are sitting on one side of the washer and a set of sheets on the other, it will cause the machine to become unbalanced during the spin cycle. … The only real fix for this is to stop the washer during the spin cycle and redistribute the clothing for more balance.
Last Updated: 18 days ago – Co-authors : 9 – Users : 10