– Hit the “menu” button on the DirecTV remote control to check the connection status.
– Select “help and settings” and then “setup” to check the connection status.
Here are the top reasons: Your wireless video bridge and Genie DVR aren’t connected properly. Make sure all cables are securely plugged into your equipment and wall outlets. The wireless video bridge lost power or is restarting.
Moreover, Why is my directv receiver not connecting?
Reset the network connection on each receiver. If the receiver does not show that both Network and Internet are connected, or if Connect Now doesn’t not work, check your cable connections and reset the router and Broadband DECA. You should also unplug the SWM power inserter then plug it back in.
Secondly, How do I reset my directv server?
Locate the reset button. On most DIRECTV receivers, there is a small red button located inside the access card door. With others, the button is on the side of the receiver. Press the red button, then wait for your receiver to reboot.
Simply so, What happens if I reset my directv receiver?
The red reset button is located behind a swingout door on the front right of most DIRECTV receivers and DVRs. This will reset a bunch of the default settings on your DVR but attempt to keep your recordings. You’ll need to pair up RF remotes again, as well as setting any preferences you had before.
What does it mean when directv says no servers were detected?
You’ll see these errors when your DIRECTV equipment isn’t communicating with the main Genie receiver. Here are the top reasons: Your wireless video bridge and Genie DVR aren’t connected properly. Make sure all cables are securely plugged into your equipment and wall outlets.
26 Related Question Answers Found
How do I fix my Direct TV?
– Unplug your receiver’s power cord from the electrical outlet, wait 15 seconds, and plug it back in.
– Press the Power button on the front panel of your receiver. Wait for your receiver to reboot.
How do I fix DirecTV no servers detected?
– Make sure the DVR is plugged into power and firmly secure.
– Turn on the DVR.
– If you see a picture, press and hold the red button located near the access card.
– If you still see the No Servers Detected message on all of the Genie Minis, the DVR cable may be loose.
How do I fix directv no servers detected?
– Make sure the DVR is plugged into power and firmly secure.
– Turn on the DVR.
– If you see a picture, press and hold the red button located near the access card.
– If you still see the No Servers Detected message on all of the Genie Minis, the DVR cable may be loose.
How do I change Internet connection on directv?
– Press MENU on your remote.
– Select Settings & Help > Settings > Internet Setup > Connect Now.
– After the system checks the connection status, select Set Up Wireless.
– Select your wireless network.
– Enter your wireless network password and select Continue.
How do I reconnect my directv box?
– Press MENU on your remote.
– Select Settings & Help > Settings > Network Setup > Connect Now.
– After the system checks the connection status, select Set Up Wireless.
– Select Push Button Setup.
– Push the WPS button (the one with the logo) on your router.
How do I disconnect my directv from the Internet?
Menu > settings & help > settings > reset > reset defaults. This resets to factory defaults (recordings stay) and therefore removes internet connection until you perform the Internet setup again.
How long does directv take to reset?
Expect this process to take up to 10 minutes to complete. (Most are done in less than five minutes, but result times tend to vary.) Once it’s done, you might need to reboot the clients for them to work.
What does it mean when it says no server?
A “Cannot Find Server or DNS” Error is a message that may appear when a user attempts to access a specific website. The “Cannot Find Server or DNS Error” message means one of two things: the user’s Internet service is not available or the server in question is currently inaccessible via the Internet.
How do you reset directv remote?
– Press and hold MUTE and SELECT together until the light flashes three times.
– Press 9, 8, 1 and SELECT. The remote flashes four times and should now reset.
Why is my directv internet not working?
If you see an error about no internet connection, you will need to go to your DirecTV menu. Then go to Settings & Help. Select Network Setup and Connect Now. Most of the time, setting up the Internet connection again and or rebooting the router will solve the problem.
How do I reconnect my directv?
– Press MENU on your remote.
– Select Settings & Help > Network Setup > Restore Defaults.
– Once the receiver has completed restoring its default settings, select Connect Now.
– If the receiver doesn’t connect, you can reset it.
Why is my directv not working?
If you cannot locate the red reset button or your receiver does not have one: Unplug the receiver’s power cord from the electrical outlet. Wait 15 seconds then plug it back in. Press Power on the front panel of your receiver and wait for your receiver to reboot.
Last Updated: 14 days ago – Co-authors : 12 – Users : 8
