Connect the hub to the household’s broadband router using the network cable provided. Fit the power cable into the hub and plug it into a power socket. OOO Wait for an amber flashing light. During start up the green light will flash, followed by the amber light.
Also, How do I use the hive thermostat?
Hereof, How do I put my hive thermostat in pairing mode?
If you already have a Hive Hub just put it into pairing mode. To do this press the button at the rear of the hub for 1 second and release it. The middle light should now flash AMBER showing it is in pairing mode.
How do I setup my hive?
– Connect your hub to your broadband router using the Ethernet cable in the box.
– Connect your hub to a mains power socket using the power cable in the box.
– For the hub to work at its best you should avoid placing it on the floor or in an enclosed area such as a cupboard.
Likewise, Why is my hive not connecting?
Check that your Hive hub is connected to the mains power socket and switched on. Check that your products are connected to the mains power socket and the socket is switched on OR that the batteries haven’t run out. For help on replacing the batteries see our user guides.
17 Related Question Answers Found
How do I connect my phone to my hive?
In order to connect the receiver to the hub, you will need put the hub into pairing mode. You can do this by selecting ‘Install devices’ within the Hive app menu. From there tap ‘Add another device’ and then ‘Go’ which will start the hubs search.
How do I put Hive plug in pairing mode?
If you’re trying to pair your Hive Active Plug and you don’t see a light on the front flashing amber you may need to reset it. To reset your Hive Active Plug, press and hold the button on the front for ten seconds. Once you see the light double flashing amber, you’re done!
How do I pair my hive thermostat?
If you already have a Hive Hub just put it into pairing mode. To do this press the button at the rear of the hub for 1 second and release it. The middle light should now flash AMBER showing it is in pairing mode. Then move on to stage 2.
Does hive work without a thermostat?
Do I need to have a thermostat already for Hive Active Heating? No, you don’t need to have an existing thermostat but if you have one the Hive thermostat would replace it.
How do I keep the hive thermostat on?
The “Hold” setting will keep your home at a constant temperature. On the app, Select Hold in the “System settings” screen. On the web, select the Hold section on the web dashboard. On the thermostat, tap Menu.
Can hive work on two phones?
As the hub will be registered to your account just make sure you are using your login Though you can use multiple mobile devices, only one account, for example same email address and password, as the Hive hub is registered to one account.
How do I reset my hive app?
To reset your Hive Active Plug, press and hold the button on the front for ten seconds. Once you see the light double flashing amber, you’re done! Try installing your Hive Active Plug in your Hive app or online dashboard again.
How do I set the hive thermostat?
– Wake up your thermostat by pushing the dial and then press the Menu button.
– Turn the dial to select Heat and push the dial to confirm.
– Select Schedule and push the dial.
– To set up a new heating schedule scroll to Start Over and push the dialStep 5 Follow the on screen instructions to create your new schedule.
How do I add users to hive?
What is the default username and password for hive?
admin
How do I connect my hive thermostat to my phone?
In order to connect the receiver to the hub, you will need put the hub into pairing mode. You can do this by selecting ‘Install devices’ within the Hive app menu. From there tap ‘Add another device’ and then ‘Go’ which will start the hubs search.
How do I reset my hive?
The Hive Hub can be reset by pulling the power cable out and putting it back in again. It will take about 5 minutes to fully reboot and pair to your devices. After the 5 minutes, refresh the app or website.
Last Updated: 2 days ago – Co-authors : 14 – Users : 8