Operating Frequency 2.400 – 2.483 GHz
————————— ———————————————————————————————–
Max Transmission Distance FCC Compliant: 3.1 mi (5 km) CE Compliant: 2.2 mi (3.5 km) (Unobstructed, free of interference)
Operating Temperature Range 32° to 104°F (0° to 40°C)
Battery 6000 mAh LiPo 2S
Transmitter Power (EIRP) FCC: 20 dBm CE: 16 dBm MIC: 16 dBm
Moreover, How far can the Phantom 3 standard fly?
roughly 350 feet
Secondly, How do I connect my remote to my drone?
Turn on the aircraft. Press and hold the RC Binding button on the side of the aircraft (shown below) for about 3 seconds. The binding indicator next to the RC Binding button will slowly flash green indicating the aircraft is ready to rebind. buttons simultaneously on the remote controller for a few seconds.
Simply so, How do I connect my drone to my controller?
Turn on the aircraft. Press and hold the RC Binding button on the side of the aircraft (shown below) for about 3 seconds. The binding indicator next to the RC Binding button will slowly flash green indicating the aircraft is ready to rebind. buttons simultaneously on the remote controller for a few seconds.
How far can a phantom 3 fly?
Operating Frequency 5.725 – 5.825 GHz, 922.7 – 927.7 MHz (Japan)
————————— ——————————————————————————————
Max Transmission Distance FCC: 1000 m CE: 500 m (outdoors and unobstructed, aircraft’s altitude at 400 feet (120 m))
Operating Temperature Range 32° to 104°F (0° to 40°C)
Battery 2600 mAh LiPo 18650
25 Related Question Answers Found
How do I pair my DJI Phantom controller?
– Turn on the remote controller, connect it to your mobile device and launch the DJI GO app.
– Power up the Phantom 4 Battery.
– Select ‘Camera’, press the remote controller icon, then tap the ‘Linking RC’ button.
How do I reset my phantom 3 remote?
Option 1: Turn on the remote controller then, while holding down the C1 and C2 buttons on the back of the remote controller, press the camera settings dial to reset. Option 2: Flick the flight mode switch back and forth until the remote controller status indicator blinks red and green.
How do I pair my DJI Phantom 2 controller?
What is the difference between phantom 3 standard and advanced?
The one major difference between the Phantom 3 Standard and the Phantom 3 Advanced is the accents. The Standard has red accents around its arms and the Advanced comes with silver accents. One other slight difference: the Phantom 3 Advanced weighs 64 grams (0.1 pounds) more than the Phantom 3 Standard.
Why is my drone not connecting?
When your drone and controller do not connect, it might be caused by several issues. The connection can get lost due to low battery power. First, make sure the drone is fully charged. Check if the batteries of the controller are powered enough.
Why does my phantom 3 lose signal?
Inspect The RC and Phantom 3 Cracks may signal that there could be some internal damage to the transmitter / receiver or flight controller. Keep your quadcopter, the DJI remote controller and your device clean at all times. Some ground in dirt on the wrong part of the drone may just be be blocking the signal.
How do you disassemble a phantom 3?
Does the Phantom 3 have obstacle avoidance?
The first and most important difference between the two Phantom models is obstacle avoidance. The Phantom 3 has two cameras. It has one camera for video and one for stabilization. With the Phantom 4, they’ve added three more cameras for improved stabilization and obstacle avoidance.
How do I connect my phantom 4 Pro to my controller?
How do you connect a DJI Phantom controller?
– Turn on the remote controller, connect it to your mobile device and launch the DJI GO app.
– Power up the Phantom 4 Battery.
– Select ‘Camera’, press the remote controller icon, then tap the ‘Linking RC’ button.
How do I reset my DJI Phantom controller?
How do you do a hard reset on a normal p4p remote. You can hold the three bars on the right side of DJI GO 4 for 10 seconds to refresh the firmware. Alternatively, you can turn on the RC, hold C1, C2, and the record button, then turn off and turn on the RC again to check.
How do I pair my phantom 3 remote?
Press the linking button on the Phantom 3 using a straightened paper clip or other thin object. After a few seconds, the link light on the Phantom 3, which is just behind the link button, will turn green. Your remote controller is now linked to the Phantom 3.
Last Updated: 19 days ago – Co-authors : 14 – Users : 8
