How do I clear the error code on my Whirlpool washer?

0
6658

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

Read the full answer

Code Meaning
—- ————————————————————————
FL The washer failed to lock the door.
Hr Washer temperature control problem.
LE The washer has tried to fill but has not reached the proper water level.
LO The door will not unlock.

Beside this, What does F 01 mean on a washing machine?

failed electronic machine control board

Likewise, How do you reset a front load washer?

– Press POWER to turn the washer off.
– Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
– With the power disabled, press and hold the START/PAUSE button for 5 seconds.
– Plug the washer back in, or turn the circuit breaker back on.

Also, What does F 02 mean on a washing machine?

long drain time

How do you reset a washing machine?

First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians.


16 Related Question Answers Found

 

How do I reset my fully automatic washing machine?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.

What does Fl mean on a Whirlpool washer?

F8 E1 or LF or LO FL Error Code in the Display of my Whirlpool Washer. Error Code F8 E1, LF, or LO FL all indicate that no water is detected entering washer after 13 minutes.

How do you clear the error code on a Whirlpool Duet washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do you reset a Whirlpool washing machine?

– Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
– The motor has now been reset and is ready for you to start a cycle.

How do you reset a Whirlpool front load washer?

– Turn off the washer.
– Turn the mode dial to NORMAL.
– Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.

What does it mean when all lights are flashing on washing machine?

If the wash, rinse and spin function lights all flash at the same time, this would indicate a possible blockage in your filter or waste / drain pipe. We recommend checking your user manual as all models vary – you can also download your user manual here.

What does it mean when all the lights are flashing on my Indesit washing machine?

End light flashing Indicates that the Indesit washing machine has reached the end of a wash programme. If the wash, rinse and spin function lights all flash at the same time, this would indicate a possible blockage in your filter or waste / drain pipe.

How do I fix error code F02?

Press the pause or cancel button on the Whirlpool washing machine to clear the F02 error code from the display, and try using it again. The error code is displayed when the washer takes more than eight minutes to drain, but may just be a glitch.

What does fo1 mean on washing machine?

failed electronic machine control board

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

Why is my washer not draining or spinning?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

Why is the washing machine not starting?

The lid switch is under the lid. … If your washer will not start, be sure the switch is being pressed. If the lid switch is being pressed but no power is being supplied to the washers motor, then the switch is most likely bad. To test the switch, turn off power to washer and remove the wires from the lid switch.


Last Updated: 10 days ago – Co-authors : 10 – Users : 4

LEAVE A REPLY

Please enter your answer!
Please enter your name here