The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Beside this, Which side of roofing felt goes down?
It has to go rougher side up, but there is no specific top or bottom. Make sure the felt placed higher up overlaps the lower piece. Do I need to spread a layer of tar on the roof before laying the felt? You don’t need to apply any tar before laying the felt, however it depends on your needs.
Likewise, How do you apply drip edge?
Also, Does fascia go under drip edge?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Does roofing felt go over or under drip edge?
Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
17 Related Question Answers Found
Where does the drip edge go?
Drip edges are metal sheets, usually shaped like an “L,” installed at the edge of the roof. Also called drip edge flashing or D-metal, they serve a vital function by directing water away from the fascia and into the gutter.
How do you apply roofing felt?
Installing roof felt is a two-person job. Nail metal drip-edge flashing, which bends over the roof and down the edge of the facing board, on all roof edges. Fasten drip edge on eaves with galvanized nails and a hammer, about 12 inches apart, before laying roof felt.
Does drip edge go over fascia?
How do you install roofing felt?
Installing roof felt is a two-person job. Nail metal drip-edge flashing, which bends over the roof and down the edge of the facing board, on all roof edges. Fasten drip edge on eaves with galvanized nails and a hammer, about 12 inches apart, before laying roof felt.
Does drip edge go under roof felt?
It depends on where the drip edge is. At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.
Do you install drip edge before fascia?
The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.
Which way up does roofing felt go?
It has to go rougher side up, but there is no specific top or bottom. Make sure the felt placed higher up overlaps the lower piece. Do I need to spread a layer of tar on the roof before laying the felt? You don’t need to apply any tar before laying the felt, however it depends on your needs.
What do you stick roofing felt down with?
Tack it in place at the corner, with the end flush with the end of the roof and the bottom edge of the roll right along the bottom of the roof deck, over the drip edge. Roll out about 10 feet of felt and fasten with staples or roofing nails with plastic washer heads. Use a construction stapler or a hammer.
Should drip edge match fascia or shingles?
The most common colors for drip edge are white and brown. However, some roofing companies can provide color match drip edge. The color is often chosen to match the shingles or the gutters to create a seamless look. The color can also be chosen to match the shutters or trim of the house and act as an accent color.
Does drip edge go over or under ice and water shield?
(The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.) You should install ice and water protector before other underlayments, including roof felt. Around roof features like dormers and chimneys, you should place ice and water protector below flashing.
How do you attach drip edge?
What is the best adhesive for roof felt?
EVERBUILD BLACKJACK 904 Bitumen Roof Felt Adhesive is the ultimate cold applied, bitumen-based adhesive used to bond roofing felt to most surfaces metal, concrete, timber and more. It provides an incredible high bond strength which delivers a tough but flexible film that hardens and softens with changing temperatures.
Last Updated: 8 days ago – Co-authors : 7 – Users : 6