- Can you lay or store your outboard on your side?
- Yes, this can be done though err on the side of caution.
- Before you do its always best to check the owner’s manual to ascertain the recommended way to store your motor on its side.
Thus, How do you store a 2 stroke outboard motor?
Additionally How far below the bottom of the boat should the prop be? If you have a short shaft motor, the top most part of the transom and the lower most part of the boat should be about 15 to 16 inches.
How do you store a 4 stroke outboard motor?
Is it bad to lay a boat motor on its side? It’s almost never a good idea to lay an outboard motor down on its side or back. This is doubly true in the winter, when moisture from condensation needs to drain from the motor. Evinrude/Johnson emphatically states that four-stroke motors must be stored upright and recommends this for all other motors.
Should you run your outboard out of gas?
It’s best to get all of the gas out of the engine’s fuel system for that season that it sits. And generally, the easiest way to do that is going to be to just unhook the gas. And let the engine run until it dies, because it is out of fuel.
Should you run a 2 stroke outboard dry?
Both should be cleaned. That dos’nt mean you should run it dry unless you want no oil to protect the engine while it’s stored.
Should you run a 2 stroke dry?
I found out the hard way that if the motor is a two-stroke you should not let it run until it stops, but rather stop it deliberately when it starts to run roughly. This will ensure that there is a coating of fuel and oil in the cylinder, and protect against rust in storage.”
Can you run an outboard tilted up?
The engine must be warmed up to open the thermostat and circulate water throughout the engine’s cooling passages completely. The engine can be vertical or tilted. Remove the prop, and run in neutral at no more than an idle speed for at least five minutes.
How do you support an outboard when trailering?
What angle should my outboard be?
The boat motor sits in a neutral position when the propeller is parallel with the top of the water and the motor shaft is at a 90 degree angle. This position normally provides the most efficient operation of the motor and boat in normal conditions.
Do I need to flush outboard every time?
Most outboard manufacturers recommend a freshwater flush after every use in saltwater to clear the cooling passages of salt residue and scale that can accumulate and impede the flow of vital cooling water through the engine.
Should I trim up in shallow water?
When idling through very shallow water, don’t trim the outdrive up as far as possible. Do so, and if you run aground you’re out of options. Leave it a couple inches down, however, and if you run aground you can tilt it up that last little bit and still have the ability to back off and seek a deeper path.
Do you really need a transom saver?
the correct answer is,yes,you need a transom saver. even though boats are designed to flex and move in the water,they are not designed to be rigidly mounted to a trailer with a motor bouncing on the back that is flexing and stressing the transom with every bounce.
Does Mercury Marine recommend a transom saver?
While there is a lot of debate on the transom savers or motor support issue, we do not recommend trailering using your service/engine lock for engine support when trailering. Both Yamaha and Mercury recommend against it as well.
What year Yamaha outboards had problems?
Owners of some Yamaha outboards are incensed at having to pay thousands to repair their relatively low-hour engines. Recently, the BoatUS Consumer Protection Bureau has been made aware of dozens of reports regarding serious corrosion problems in Yamaha outboards, specifically 2000 to 2004, first-generation F225 models.
Does all the water drain out of an outboard motor?
How long can you run an outboard on muffs?
For larger engines, use the flush port or a set of flushing muffs. Water pressure should be set to one-half or more to ensure adequate flow to the intakes. The engine should be run for five to 10 minutes.
How much water should be coming out of outboard?
Usually the cooling water pisses out of a small hole under the power head. There should be a hols approx 3 mm diameter facing down and a bit out. Normally a continuous flow expected, unless mercs are totally different.
Is it OK to leave outboard tilted up?
It’s best to tilt your outboard up when leaving your boat in the water to prevent marine growth from forming and from corrosion eating away at its metal parts. That being said, there are some instances when you may prefer tilting your outboard down.
Is it OK to leave boat lift in water?
Leaving your boat lift in the water could result in damage from freezing conditions, especially if you live in an area where ice movement is common. A wheel kit from ShoreMaster can make boat lift removal as easy as rolling it out of the water, and your boat lift can easily sit on those wheels or its pads.
