If you mean “can you put screws into James Hardie siding” the answer is yes.
Therefore, drywall screws or nails will not work for cement boards. The fasteners designed for use with drywall do not feature the corrosion- and alkali-resistant coating that enables the cement board or galvanized fasteners to last.
Beside this, What kind of screws do you use for durock?
C. DUROCK Steel Screws, 32 mm (1-1/4) long, are used for applying 12.7 mm (1/2) DUROCK Cement Board to walls or ceilings. D. DUROCK Steel Screws, 42 mm (1-5/8) long, are used for applying 15.9 mm (5/8) DUROCK Cement Board to walls or ceilings.
Likewise, Do you nail or screw cement board?
Fasten HardieBacker cement board with specified nails or screws (as listed in “Materials Required”) every 8” over the entire surface. Keep fasteners between 3/8″ and 3/4″ from board edges and 2″ from board corners. Prior to setting the tile, fill all joints with the same mortar used to set the tiles.
Also, What screws should I use for cement board?
To attach the cement board to the studs, you’ll need special 1-1/4 in. cement board screws (see Fig. B). These screws have a coating to resist corrosion, a special wide head with cutting flutes and hi-low threads for a strong grip. If you can’t find them at a home center, call tile specialty stores.
What type of screws do you use for cement board?
Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place.
25 Related Question Answers Found
What kind of screws do you use for backer board?
The Backer-On 1-5/8 in. Cement Board Screws are designed for attaching HardieBacker or equivalent fiber cement backerboard to wood or light gauge steel studs. Backer-On’s patented serrated head design countersinks for flush seating at any angle, providing a smooth surface for tile.
Can I use deck screws for cement board?
It’s best to use the cement board screw, but a deck screw will do just fine.
How do you screw into cement board?
Drill a small hole in one end of a scrap of wood, attach it to the cement board at the center of the circle, screwing through the cement board into the work surface below. Then screw in a “cutter” screw where you want the circle to be scored, for example, 2 in. from the center for a 4-in. hole.
What screws to use with Hardibacker?
What type of fastener do you recommend for floor and wall applications of HardieBacker® cement board? In compliance with the tile industry, James Hardie recommends 1-1/4” long galvanized or stainless steel roofing nails (0.121” shank x 3/8” HD) or 1-1/4” long corrosion resistant ribbed waferhead screws (No.
What kind of screws do I use for cement board?
Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place.
What type of screw is used for cement board?
Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place.
Can you put screws in Hardie board?
What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.
Can you use deck screws on Hardie board?
The Hardi needs a moisture barrier attached to the studs behind the Hardi, or, waterproofing on the surface of the Hardi but not both. Weight on the wallboard (Hardi) isn’t the issue with using the proper screws. The screws should be alkali resistant, galvanized deck screws don’t qualify.
Do you need special screws for backer board?
To attach the cement board to the studs, you’ll need special 1-1/4 in. cement board screws (see Fig. B). These screws have a coating to resist corrosion, a special wide head with cutting flutes and hi-low threads for a strong grip. If you can’t find them at a home center, call tile specialty stores.
How do you drill into cement board?
It can be cut and drilled just like wood. However, drilling through cement-fiber siding goes better if you use a carbide drill bit, as opposed to a regular steel drill bit. Cement-fiber siding can be drilled while installed on a house or prior to installation.
Can you screw into Hardie board siding?
If you mean “can you put screws into James Hardie siding” the answer is yes. Otherwise, you may have landed on the wrong website. James Hardie boards can technically be drilled like wood, but it is best to use a masonry bit to drill this tough fiber-cement board.
Do you need a special drill bit for cement?
Drill bits that can drill through concrete are called masonry bits. They are also good for drilling through brick and stone. Drill bits with a tungsten carbide tip are the strongest; when it comes to solid concrete, the sharper the better. Masonry bits cut holes through concrete in two steps.
Last Updated: 11 days ago – Co-authors : 6 – Users : 6