Unplug the washer or disconnect the power for one minute and reconnect it again. Reselect the cycle and press Start. If the code persists, Contact Us or Schedule Service Online so a qualified technician can diagnose the washer.
If your washing machine is not working correctly it’s safe to say it’s developed a fault. A flashing FP or F9 E1 error code on the LCD display can ring alarm bells, but it’s typically associated with a water draining problem inside the drum.
Beside this, How do you reset a Whirlpool washing machine?
– Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
– The motor has now been reset and is ready for you to start a cycle.
Likewise, What does E1 mean on a Whirlpool washer?
drain pump system problem – long drain
Also, How do you reset a washing machine?
First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
18 Related Question Answers Found
How do I fix E1 error on my Whirlpool top load washer?
– Unplug the washer or disconnect the power for one minute.
– Plug in the washer or reconnect the power.
– Re-select the cycle and press Start.
What does E1 mean on Whirlpool washer?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water.
How do you clear the error code on a Whirlpool top load washer?
Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).
How do I run a diagnostic on my Whirlpool washer?
Is there a way to reset a Whirlpool washer?
How do you reset a Whirlpool washing machine? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
What is the meaning of E1 in Whirlpool washing machine?
drain pump system problem – long drain
How do I fix E1 error on washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
What causes a washing machine to stop working?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
How do you reset the code on a Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you fix a washing machine that won’t turn on?
– Activate the power button.
– Test the outlet.
– Reset outlet if necessary.
– Make sure the power cord is plugged in.
– Check if fuses are blown or the circuit breaker is thrown.
– See if Delay Start has been pushed.
– See if Control Lock has been activated.
How do I fix 1E error on my Samsung washing machine?
– Do a hard power reset. You need to unplug your Samsung washing machine for about 5 minutes as this will normally reset most of the electronic glitches or any other issues with software that may be present. …
– Ensure proper wire connection. …
– Replace the pressure switch.
Last Updated: 17 days ago – Co-authors : 5 – Users : 9
